Having trouble trying to change port number from 7777.
Ive editted in the GUI and get the "you need to restart SAB for this to take effect" it also shows the current IP and the new port number but then when I reload the page its always back to 7777.
I have tried changing it in these documents, stopping the service, changing the file, restarting the service but still defaults back to 7777.
sudo nano /etc/default/sabnzbdplus
sudo nano ~/.sabnzbd/sabnzbd.ini
Unable to change port number from 7777
Forum rules
Help us help you:
Help us help you:
- Are you using the latest stable version of SABnzbd? Downloads page.
- Tell us what system you run SABnzbd on.
- Adhere to the forum rules.
- Do you experience problems during downloading?
Check your connection in Status and Interface settings window.
Use Test Server in Config > Servers.
We will probably ask you to do a test using only basic settings. - Do you experience problems during repair or unpacking?
Enable +Debug logging in the Status and Interface settings window and share the relevant parts of the log here using [ code ] sections.
Re: Unable to change port number from 7777
Are you also specifying the port when launching SABnzbd?
If-so, it may be overriding the setting in sabnzbd.ini
If-so, it may be overriding the setting in sabnzbd.ini
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Unable to change port number from 7777
That is a good point, Im not too experienced in linux, if you could tell me how I could check that would be appreciated, I installed it using the following guide:
https://tteck.github.io/Proxmox/
bash -c "$(wget -qLO - https://github.com/tteck/Proxmox/raw/main/ct/sabnzbd.sh)"
https://tteck.github.io/Proxmox/
bash -c "$(wget -qLO - https://github.com/tteck/Proxmox/raw/main/ct/sabnzbd.sh)"
Re: Unable to change port number from 7777
hmmm ok I found this in /etc/systemd/system/sabnzbd.service
[Unit]
Description=SABnzbd
After=network.target
[Service]
WorkingDirectory=/opt/sabnzbd
ExecStart=python3 SABnzbd.py -s 0.0.0.0:7777
Restart=always
User=root
[Install]
WantedBy=multi-user.target
I am assuming this could be it? can i just remove the port number or do i need to remove the switch and IP, or one and not the other etc
[Unit]
Description=SABnzbd
After=network.target
[Service]
WorkingDirectory=/opt/sabnzbd
ExecStart=python3 SABnzbd.py -s 0.0.0.0:7777
Restart=always
User=root
[Install]
WantedBy=multi-user.target
I am assuming this could be it? can i just remove the port number or do i need to remove the switch and IP, or one and not the other etc
Re: Unable to change port number from 7777
ahh thank you so much OneCD...I modified this file to the following and it finally worked, for anyone else looking at this you need to keep 0.0.0.0 (at least I did) otherwise it wouldn't load.
[Unit]
Description=SABnzbd
After=network.target
[Service]
WorkingDirectory=/opt/sabnzbd
ExecStart=python3 SABnzbd.py -s 0.0.0.0
Restart=always
User=root
[Install]
WantedBy=multi-user.target
Also realised this was evident in the settings found on http://10.0.0.17:7777/config/ under the "Parameters" heading
[Unit]
Description=SABnzbd
After=network.target
[Service]
WorkingDirectory=/opt/sabnzbd
ExecStart=python3 SABnzbd.py -s 0.0.0.0
Restart=always
User=root
[Install]
WantedBy=multi-user.target
Also realised this was evident in the settings found on http://10.0.0.17:7777/config/ under the "Parameters" heading
Re: Unable to change port number from 7777
I’d remove the listening address and the port number. See how it runs. If there’s an issue, you can always put back the listening address. It should be in the SABnzbd config file anyway.
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Unable to change port number from 7777
Ah, just saw your reply.
Good work mate.
Good work mate.
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Unable to change port number from 7777
thanks for your help would not have known where to look