Support Forum

Ran memtest for nearly 4 hours earlier and only got 1 error. Ouch. Memory problems are not acceptable: they will cause all kinds of strange problems. Do you have two (or more) memory modules? If so, can you remove the memory module that causes the problem, and then run memtest again? If your system...

stop SABnzbd, find the file sabnzbd.ini and remove it, then start SABnzbd

HTH

After you clicked Retry, was there any additional download? I don't see any download at all in your log: no "missing" message like in your earlier log.

If there is no additional download, it's probably a hardware error. Can you run memtest?

In http://localhost:8080/sabnzbd/config/categories/ ? Define a post-process script for the Default category?

Is the extension .CMD OK for Windows? Can you run the script from a CMD-box? What if you rename to .BAT?

Is .CMD in your PATHEXT?

I would start by putting a 'logger' in the renamer.cmd: something that writes a message + date to a separate logfile. I haven't got Windows here, but DOS/WIndows must have a DATE command. If so "DATE ... >>> C:\temp\mylogfile.log" should work. Do it before and after the java call.

I'm thinking the problem is not in SAB, but on the newsserver side; if a message is missing, but in a retry it is there, that's a newsserver problem (or it's too new). The method to determine this: check your log file for the article number. (If you have 'grep', it's easy). Lower newsserver connecti...

A few remarks: There are a lot of missing articles in your pastebin paste. If you retry (and it works), does the log show the same missing articles? If not, the articles are suddenly there, apparently. So: do you download too new posts which are still being uploaded? Does your brother have an extra ...

I guess it's an older and somewhat slow system. If the pause-download solves the problem, I would leave it like that. Given the speed of your system, parallel download and post-processing might be slower than working sequential. Shy, the AMD Sempron 3000+ is a 1600 / 1800 / 2000 MHz processor. I'm ...

See log below, it always just stops working while decoding. *filenames changed 2011-10-15 21:02:45,580::INFO::[assembler:85] Decoding /usr/share/sabnzbd/Downloads/incomplete/xxxxxxxxxxxxxxxxxxxxxxxxxxxx.r11 yenc 2011-10-15 21:04:56,561::INFO::[__init__:838] Saving data for totals9.sab in /usr/share...

See log below, it always just stops working while decoding. *filenames changed 2011-10-15 21:02:45,580::INFO::[assembler:85] Decoding /usr/share/sabnzbd/Downloads/incomplete/xxxxxxxxxxxxxxxxxxxxxxxxxxxx.r11 yenc 2011-10-15 21:04:56,561::INFO::[__init__:838] Saving data for totals9.sab in /usr/share...

I am having the same problem. I am running 6.9.0 on Arch Linux. It will run for a day sometimes, maybe 10 minutes, maybe an hour. The logs show that it stops after decoding with yenc. I have tried rolling back yenc and still getting the same result. I would do this: run sabnzbd / sabnzbdplus from t...

I've deleted that nzbd and downloaded a different one. The failure said that it couldn't repair it. Don't recall the exact wording but it wasn't much more than "didn't work" or I would have copied it. Wait until the problem occurs again, and then copy-paste the exact error message into th...

I'm having an issue with a file that I downloaded. I'm completely new to Sab but I've gotten two files to download -- using SickBeard + Sab. Well, one to download and one to fail. I tried to repair the failed download and it failed. And what did SABnzbd say in the WebGUI? What was the error message?

If I read http://wiki.sabnzbd.org/configure-servers-v2 , I don't think Optional does what you want.

But anyway: why not try the setup you describe?