hi. no it's headless. I'm using another PC on same network
Error updating to v3 [OSMC / Debian]
Forum rules
Help us help you:
Help us help you:
- Are you using the latest stable version of SABnzbd? Downloads page.
- Tell us what system you run SABnzbd on.
- Adhere to the forum rules.
- Do you experience problems during downloading?
Check your connection in Status and Interface settings window.
Use Test Server in Config > Servers.
We will probably ask you to do a test using only basic settings. - Do you experience problems during repair or unpacking?
Enable +Debug logging in the Status and Interface settings window and share the relevant parts of the log here using [ code ] sections.
Re: Error updating to v3 [OSMC / Debian]
OK, then you need to put the IP address of the device hosting SABnzbd into your browser address bar.
If you use localhost or 127.0.0.1 in your browser, this is a request to your PC, not the server.
If you use localhost or 127.0.0.1 in your browser, this is a request to your PC, not the server.
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Error updating to v3 [OSMC / Debian]
Doh! APologies as it's a while since I've done a clean set up.
Progress - it says 'file not found' now.
Re: Error updating to v3 [OSMC / Debian]
Great!
What is the URL you’re now using in your browser?
What is the URL you’re now using in your browser?
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Error updating to v3 [OSMC / Debian]
http://192.168.0.10/8080/sabnzbd
I'm also using noip so it's accessible from outside network but that's currently not working either
I'm also using noip so it's accessible from outside network but that's currently not working either
Re: Error updating to v3 [OSMC / Debian]
Your address syntax is close, but not quite right.
The IP address and port number should be separated by a colon :
Try 192.168.0.10:8080
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Error updating to v3 [OSMC / Debian]
192.168.0.10 refused to connect.
Re: Error updating to v3 [OSMC / Debian]
strange - it just started working. I just opened kodi webinterface at 192.168.0.10 then tried sab again and works both on local and external network
Cheers for the help as this was really annoying me!
Cheers for the help as this was really annoying me!
Re: Error updating to v3 [OSMC / Debian]
Good work.
Stuff I like: Apache bash cron DD-WRT Debian DNSMasq Entware FireFox GitHub ImageMagick Kate KDE LibreELEC Netrunner NFS NVIDIA OpenVPN Orvibo-S20 pfSense Python Raspberry-Pi RAID SABnzbd Transmission Usenet VirtualBox Watcher3 XFCE
Re: Error updating to v3 [OSMC / Debian]
Spoke to soon, while it is running , it is running v1.1.1 . I used these instructions:
From the standard Debian contrib repository
First make sure you have the Debian repository contrib activated. Then
sudo apt-get install sabnzbdplus
I then used the git instructions on the same page and all installed. I can run sabv3 from directory fine but how can I set v3 to run at boot rather than v1?
Thanks
From the standard Debian contrib repository
First make sure you have the Debian repository contrib activated. Then
sudo apt-get install sabnzbdplus
I then used the git instructions on the same page and all installed. I can run sabv3 from directory fine but how can I set v3 to run at boot rather than v1?
Thanks