Not sure when but Direct Unpack stopped working at some point in my install of SABnzbd (2.3.2). I went back about 20 history pages and none of them say they were Direct Unpacked. I confirmed the setting is enabled and my temp drive is an SSD with write speeds well over the requirement.
Not a whole lot in the log but this appears for each download:
INFO::[directunpacker:372] Aborting DirectUnpack for None
Edit: Updated to 2.3.3, same problem. I then downgraded to 2.3.0 and it works again. So I'll stick with that for now.
Edit2: This ended up being due to my indexer inserting a single fake article into NZBs for tracking purposes. Safihre was very helpful and helped me to setup the developer version of SAB and remove the missing article check in the direct unpack function to get it working in my scenario.
Direct Unpack Not Working "Aborting DirectUnpack for None"
Forum rules
Help us help you:
Help us help you:
- Are you using the latest stable version of SABnzbd? Downloads page.
- Tell us what system you run SABnzbd on.
- Adhere to the forum rules.
- Do you experience problems during downloading?
Check your connection in Status and Interface settings window.
Use Test Server in Config > Servers.
We will probably ask you to do a test using only basic settings. - Do you experience problems during repair or unpacking?
Enable +Debug logging in the Status and Interface settings window and share the relevant parts of the log here using [ code ] sections.
Direct Unpack Not Working "Aborting DirectUnpack for None"
Last edited by PiERiT on May 5th, 2018, 2:20 pm, edited 3 times in total.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
You shouldn't be on 2.3.0, it has a number of bugs.
Maybe you can enable +Debug logging (on 2.3.3) in the Status and Interface settings window and then download something again that should Direct Unpack. Then send me the log (click Show Logging) at [email protected]
Maybe you can enable +Debug logging (on 2.3.3) in the Status and Interface settings window and then download something again that should Direct Unpack. Then send me the log (click Show Logging) at [email protected]
If you like our support, check our special newsserver deal or donate at: https://sabnzbd.org/donate
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Sure, I will do that later today.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Sent. Thank you.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
In this case the problem was:
When we detect missing articles, we don't start Direct Unpack since we can be 99% sure it will fail.
Code: Select all
2018-04-23 18:52:22,948::DEBUG::[nzbstuff:1435] Download Quality: bad-articles=1
If you like our support, check our special newsserver deal or donate at: https://sabnzbd.org/donate
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Is that a change since 2.3.0? That same download direct unpacked in that version. 99% of my downloads direct unpack on 2.3.0, whereas 0% do on 2.3.2 and later.
I noted in the History tab that every download states "1 articles was missing", regardless of version.
I noted in the History tab that every download states "1 articles was missing", regardless of version.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Maybe you can send me some example NZBs?
It's a bit strange, should only Abort after 5 bad articles.
It's a bit strange, should only Abort after 5 bad articles.
If you like our support, check our special newsserver deal or donate at: https://sabnzbd.org/donate
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
I will send you the one I've been testing with. It always direct unpacks in 2.3.0 and never does in 2.3.3.
Thanks for the help. Very strange indeed.
Thanks for the help. Very strange indeed.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
I have the same issue too with my indexer injecting a single fake article that causes direct unpack not to start. Can you tell me how to remove the missing article check? Thanks!
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
What OS are you on?
If you like our support, check our special newsserver deal or donate at: https://sabnzbd.org/donate
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Windows 10 64-bit
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Start with this: https://sabnzbd.org/wiki/installation/i ... ce-windows
The rest of this isn't exact, but when that's done, go to %userprofile%\sabnzbd (or wherever you installed to), then another folder called sabnzbd, then edit the directunpacker.py file. I don't have the original file anymore, so I don't recall precisely what it said, but in the check_requirements section, there's something like 'self.nzo.missing.articles' that you want to remove whilst leaving the other checks. So my line now reads:
if not cfg.direct_unpack() or self.killed or not self.nzo.unpack or sabnzbd.newsunpack.RAR_PROBLEM:
After that edit, save the file and compile it -- from command prompt run 'python %userprofile%\sabnzbd\sabnzbd\directunpacker.py'.
Hope that helps.
Re: Direct Unpack Not Working "Aborting DirectUnpack for None"
Thank you, that worked!